With CFR machines you get:
Faster
cleaning
More
thorough cleaning
Faster
drying
Safer
cleaning
Less
operator fatigue
Sounds
to good to be true? We thought just the same - until we got our hands
on one. Just take a look at what these machines can do for you:
6
reasons why CFR machines clean faster, better and easier
1.
High pressure cleaning solution shears away the dirt - FAST!
CFR's
patented ‘air induction' tooling means you can clean at very high
pressure, but without over wetting. You get up to ten times
more power than a conventional 100psi extractor!
With
CFR's patented 'air induction' tooling, the cleaning solution atomises
at high velocity - it literally shears away the dirt for you.
You
get the more thorough cleaning faster - with fewer passes of the wand,
and with less effort from the operator. You've got to try one of these
machines!
No need for time-consuming mechanical agitation
With
low pressure machines, for best results the operator needs to put down
a pre-spray, then agitate mechanically (e.g. with a power brush). This
loosens the soil prior to rinse extraction.
When
you clean at high pressure with CFR machines, mechanical agitation is
rarely necessary - the high pressure cleaning solution is all the agitation
you need on most jobs.
Remove
the need for mechanical agitation - and you save even more time on every
job. There's less gear to cart in and out. And it's far kinder on your
client's natural fibres too -
Just
think what happens when you scrub wool with a brush - no matter how soft
the brush is! CFR's high pressure cleaning solution gives you all the
agitation you need, but it won't tear at the wool fibres like a brush.
Yet
another reason - you've got to try one of these machines
for yourself!
Less
time spent emptying and refilling
The
problem with high pressure portable extractors is this:
High
pressure cleaning means high volumes of water - so you spend more time
emptying the waste water. And more time at the sink refilling buckets
of water.
And
if you’ve ever stood next to a combi-boiler for 10 minutes watching
a trickle of water fill up your bucket – you’ll know how time
consuming that can be!
But
not so with CFR machines!
CFR
machines continuously recycle and filter the cleaning solution. This means
you can clean up to 7 times the area - with the same amount of cleaning
solution. You also save money on extraction chemicals.
It’s
possible to clean a whole house of carpets on just one tank! Already that's
three ways a CFR machine does the job faster. But there's more.
Less time spent spot cleaning by hand
Cleaning
at high pressure means you spend less time spot cleaning. With up to 10
times more power at the wand head, more spots simply lift out during normal
extraction. yet another way CFR saves you time!
Safer
cleaning, faster drying
CFR
machines use patented ‘air induction' tools. Unlike conventional
tools, CFR tooling applies and recovers the cleaning solution in one continuous
process. But what does this mean?
When
you clean using a conventional wand, if you get the water pressure wrong
(or forget to adjust it), or move the wand too slowly – it’s
very easy to over-wet. Even at low pressures of 100psi or less.
At
best, this can mean drying times running into days. At worst, shrinkage.
Or dye releasing from the backing and wicking up to stain the carpet pile.
With
CFR tooling, there's
less
risk of damage to your client’s carpets and furniture - even in
the hands of inexperienced operators. And because up to 93% of the cleaning
solution is recovered immediately - you can expect faster drying times
too.
Less
operator fatigue
No-one
wants to go home exhausted every day. But it's more important than that!
Isn't it possible that the quality of cleaning goes down as the operator
gets tired?
Or
that personal injury and accidental damage are more likely - because it's
harder to concentrate when you're tired.
Or
that you can expect a higher turnover of staff and more days off 'sick'
- when your technician goes home exhausted every night?
Operator
fatigue leads to accidents, injuries and expensive time off work all the
time.
Carpet
cleaning is always going to be physical work. But with CFR, the high pressure
cleaning solution does much of the work for you. You make less passes
with the wand. A secondary ‘scrubbing’ process isn’t
needed. There’s less carrying of buckets of water. Less bending
for spot cleaning. And less stress on the back.
With
CFR machines, you don't just clean better - you clean easier too.
Why
carpets and upholstery cleaned with your CFR machine dry faster
Leaving
carpets drier is critical:
It is more convenient for your customers - who can use their rooms sooner
It prevents customers
from tracking more dirt on the clean but still damp carpets
It prevents mold, mildew
and fungus from forming in the wet environment
It prevents delaminating
and other damage caused by extended periods of wetness.
1.
More solution is recovered
CFR's
patented machine wands and tools are proven to recover as much s 30% more
water than conventional wands. This patented "solution control"
process keeps the cleaning solution in motion at all times so it can be
recovered immediately.
2.
Solution is kept out of the backing and pad
When
the backing and pad get wet, the solution must "wick up" to
the surface before it can start to evaporate. This process of "wicking
up" can mean drying times running into days!
CFR's
patented system prevents the solution from getting into the back and pad
so the drying process can start much more quickly. Laboratory tests prove,
carpets cleaned with CFR dry much faster. |
